Description
Finish
PROTECTOR
Synthetic, satin metallic paint, one pot system, top quality
Synthetic primer, intermediate and finishing coat for ferrous and non-ferrous, based on a special alkyd resin combination and special fillers, for indoor and outdoor use
Application
- Indoors and outdoors on ferrous metals (iron and steel) and non-ferrous metals.
- Metal doors, railings, …
Properties
- Very good primer, adhesive coat and finishing coat (one-pot system).
- Easy to process.
- Silky shine and retains its shine.
- Weatherproof.
- aromatics poor.
- Optimal substrate wetting.
- Anticorrosive Zinc Phosphate Pigmentation.
- Many colors available through HerbolColor Service.
Note: yellowing
Any alkyd-based paint will, when applied indoors, in white and pastel shades, under the influence of heat and the lack of direct daylight yellowing.
Technical data
Density: Approx. 1.2 kg/l
Binder: Special epoxy ester combination
Pigmentation: Rutile Titanium dioxide and special fillers.
Shine: Satin gloss
Colour
Can be colored via the HerbolColor Service system
Available in white + black + Base LA1 + Base LA2 + Base LA3 + Base LA4
Packaging
Basic in 1 – 2.5 and 10 L; black in 0.75 and 2.5; white in 0.75 – 2.5 and 10 lt
Storage
In original closed packaging in a cool, dry and frost-free place
VOC EU limit value
EU limit value for this product (cat A/i): 600g /L (2007) / 500g /L (2010). This product contains max. 490 g/L VOC.
Solids content
In volume about 53 %; by weight approx. 70%
Processing data
Processing
Brush, roller and spray (also airless)
Processing conditions
Apply at least 5 °C for substrate and air temperature during and after the processing.
Attention: Avoid direct sunlight, rain, mist, dew and strong wind.
Avoid condensation during morning and evening hour
PROTECTOR
Processing data
Theoretical return
Brush – roller: apply undiluted: approx. 7 m²/l or approx. 140 ml/m²
• Apply at least 100-120 µm dry film thickness on zinc and galvanized substrates.
• Apply at least 120 µm dry film thickness on iron and steel.
• Generally 3 coats (primer coat, intermediate coat and top coat) are recommended.
Drying times (at 23°C and 50% RH)
Dust-dry: after approx. 3 hours – Tack-free: after approx. 12 hours
Can be painted over: after approx. 24 hours.– Full curing after a few days
Cleaning the tools
Herbol-KUNSTHARZ-VERDÜNNUNG V40 or white spirit
Spray data airless
Dilution: undiluted
Pressure: approx. 140 to 180 bar, depending on the flow rate
Nozzle: from 0.013 inch.
Note: do not spray metallic colors airless
Safety Information
flash point > 23°C DIN 53213
Transport code UN 1263 PAINT VSE (ADR 2.2.3.1.5)
R and S sentences
R 10 Flammable
R51/53 Toxic to aquatic organisms; can be used in the aquatic environment cause harmful effects in the long term.
R 66 Repeated exposure may cause skin dryness or cracking.
R 67 Vapours may cause drowsiness and dizziness.
S 2 Keep out of the reach of children.
S 16 Keep away from sources of ignition – No smoking.
S 23 Do not breathe gas/fume/vapour/mist.
S 24/25 Avoid contact with eyes and skin.
S 29 Do not throw waste into the sink.
S 46 In case of ingestion, seek medical advice immediately and unpack the container or show label.
S 51 Use only in well-ventilated areas.
General
Ensure adequate ventilation during and after application.
In case of insufficient ventilation, wear suitable respiratory equipment.
When working on paint layers such as sanding, welding, burning, etc., hazardous dust particles and/or vapors are released. Work in a well-ventilated area. Usage
appropriate self-protection equipment when necessary.
System structure
All paintwork and necessary pre-treatments must be applied to the object adapted: ie they must be adapted to the condition, the performance requirements and the conditions to which they are exposed.
Substrate preparation
(untreated)
Iron and Steel
Derust the surfaces well. Remove dirt and degrease.
Zinc, paintable hard plastics
Sand the surfaces matt with an abrasive sponge (Scotch-Brite) and slightly ammoniacal water (10% strength). + a little detergent. Good rinse with water.
Aluminium
Degrease very thoroughly with nitro thinner and sand with scouring pad (nylon or perlon).
Copper
Treat the surfaces with a diluted hydrochloric acid solution (10% strength) then sand with a perlon fleece. Rinse well with water.
Paint system ***
• Primer: Herbol PROTECTOR.
• Intermediate layer: Herbol PROTECTOR.
• Finish: Herbol-PROTECTOR.
Note:
• Herbol PROTECTOR metallic :
• Streaking is characteristic of metallic colours.
• Treat heavily loaded surfaces with 2-component products.
PROTECTOR
The information contained in this publication has been updated in accordance with the current status of the research technique.
However, due to the versatility of application and processing methods, no liability is accepted.
Our general delivery and payment conditions apply to advice and delivery.
Reviews
There are no reviews yet.