COATING SYSTEM – MOISTURE TOLERANT EPOXY / POLYURETHANE – GLOSS COLOUR

CHOOSE PACKAGING, COLOR AND QUANTITY FOR EACH PRODUCT.

SPECIFC COLOUR CODES CAN BE ENTERED IN THE NOTE BOX DURING CHECK OUT.

Epoxy + Polyurethane

Choose Packaging
Pick Color
  • Dawn Grey
  • Yelllow Green
-
+
Choose Packaging
-
+
Choose Packaging
Pick your Color Group
  • Stdd. White
  • Cat. White / Beige
  • Cat. Yellow
  • Cat. Orange
  • Cat. Red
  • Cat. Violet
  • Cat. Blue
  • Cat. Green
  • Cat. Grey
  • Cat. Brown
  • Cat. Black
-
+

Description

Application Procedure

Surface Preparation

  1. Clean the surface from contaminents such as oil, grease, salts & chlorides using a biodegradable degreaser such as Safeclean BIO 3, followed by a rinse with clean water
  2. Remove any loose rust, paint and corrosion by abrasive blasting, UHP waterjetting or power tool cleaning.

Paint Application

Apply by brush, roller or spray:

Layer Product Name Generic Type Mix Ratio Min. Temp. Dry time @ 25°C m2/L brush m2/L spray Thinner
1st coat Intergard 5000 2  comp. epoxy primer 16 : 4 5°C 7 hrs 4,92 3,28 GTA220
2nd coat Interthane 990 2 comp. polyurethane topcoat 17 : 3 -5°C 6 hrs 10,26 6,84

Find the right application tools in the toolbox for solvent based coatings

Tips

  1. Do not apply or expose the paint below dew point, above 80% relative humidity, rain or temperatures below 10°C during application or drying.
  2. Make sure the mixing ratio is correct
  3. Wait at least 15min. after mixing before applying the paint
  4. Apply a stripe coat by brush on sharp edges, cavities such as pitting corrosion, in corners and difficult areas to reach by spray
  5. Do not overcoat a single component system with a 2 component system
  6. Respect to minimum and maximum overcoating time as per product data sheet

 

Always read the product technical data sheet and safety data sheet before using the coatings, to be found in the Download section.

Additional information

Weight 25 kg
End Use

Brand

Gloss Level

Compatible with

2 component

Substrate

, ,

Budget - Low (*) to High (*****)

***

Productivity - Low (*) to High (*****)

****

Quality - Low (*) to High (*****)

****

Surf Prep M&R

, , , , ,

Surf Prep New Steel

,

UV resistance - Low (*) to High (*****)

Systems

, , , , , , ,

Coating, Lining or PFP

Market Segment

Solvent

Layer

,

Product type

,

Detailed information about COATING SYSTEM – MOISTURE TOLERANT EPOXY / POLYURETHANE – GLOSS COLOUR

Intended usesFor maintenance above the waterline, especially in combination with UHP Waterjetting or mechanical cleaning.
Max. DFT475 µm
Min. DFT175 µm
Typical DFT225 µm
Min. application temp.-5°C
ChemistryEpoxy + Polyurethane

Downloads

Product name Document name Document type Language Download
COATING SYSTEM – MOISTURE TOLERANT EPOXY / POLYURETHANE – GLOSS COLOUR PDS Intergard 5000 Download
COATING SYSTEM – MOISTURE TOLERANT EPOXY / POLYURETHANE – GLOSS COLOUR PDS Interthane 990 Download

Reviews

There are no reviews yet.

Be the first to review “COATING SYSTEM – MOISTURE TOLERANT EPOXY / POLYURETHANE – GLOSS COLOUR”

Your email address will not be published. Required fields are marked *

Need Help?